mtd: spi-nor: spansion: SMPT fixups for S25FS-S

S25FS-S family supports SMPT that helps to detect sector layout settings
in configuration registers, but some of parameters in the table are
wrong or undetermined so the fixups below are required.

Read Any Register op is used to read configuration registers that
related to sector map. The op requires 8 cycles latency by default.
Implement smpt_read_dummy() to set correct dummy cycles.

Map ID is structured by combination of CR3NV[3], CR1NV[2], and CR3NV[1].
However, in S25FS512S, CR3NV[1] is RFU and always 0, while map IDs
defined in the table assume it is always 1. Implement smpt_map_id() to
fix map ID for S25FS512S. Other densities in S25FS-S family (256Mb and
128Mb) don't need this fix as CR3NV[1] in those chips is configurable
and map IDs are correctly defined in SMPT.

Co-developed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # S25FS512S
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>

1 files changed, 38 insertions, 0 deletions

diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
index a0296c871634..8498c7003d88 100644
--- a/drivers/mtd/spi-nor/spansion.c
+++ b/drivers/mtd/spi-nor/spansion.c
@@ -785,8 +785,46 @@ s25fs_s_nor_post_bfpt_fixups(struct spi_nor *nor,
 	return 0;
 }
 
+static void s25fs_s_nor_smpt_read_dummy(const struct spi_nor *nor,
+					u8 *read_dummy)
+{
+	/*
+	 * The configuration detection dwords in S25FS-S SMPT has 65h as
+	 * command instruction and 'variable' as configuration detection command
+	 * latency. Set 8 dummy cycles as it is factory default for 65h (read
+	 * any register) op.
+	 */
+	*read_dummy = 8;
+}
+
+static void s25fs_s_nor_smpt_map_id_dummy(const struct spi_nor *nor, u8 *map_id)
+{
+	/*
+	 * The S25FS512S chip supports:
+	 *   - Hybrid sector option which has physical set of eight 4-KB sectors
+	 *     and one 224-KB sector at the top or bottom of address space with
+	 *     all remaining sectors of 256-KB
+	 *   - Uniform sector option which has uniform 256-KB sectors
+	 *
+	 * On the other hand, the datasheet rev.O Table 71 on page 153 JEDEC
+	 * Sector Map Parameter Dword-6 Config. Detect-3 does use CR3NV[1] to
+	 * discern 64-KB(CR3NV[1]=0) and 256-KB(CR3NV[1]=1) uniform sectors
+	 * device configuration. And in section 7.5.5.1 Configuration Register 3
+	 * Non-volatile (CR3NV) page 61, the CR3NV[1] is RFU Reserved for Future
+	 * Use and set to 0, which means 64-KB uniform. Since the device does
+	 * not support 64-KB uniform sectors in any configuration, parsing SMPT
+	 * table cannot find a valid sector map entry and fails. Fix this up by
+	 * setting SMPT by overwriting the CR3NV[1] value to 1, as the table
+	 * expects.
+	 */
+	if (nor->params->size == SZ_64M)
+		*map_id |= BIT(0);
+}
+
 static const struct spi_nor_fixups s25fs_s_nor_fixups = {
 	.post_bfpt = s25fs_s_nor_post_bfpt_fixups,
+	.smpt_read_dummy = s25fs_s_nor_smpt_read_dummy,
+	.smpt_map_id = s25fs_s_nor_smpt_map_id_dummy,
 };
 
 static const struct flash_info spansion_nor_parts[] = {